For full functionality of this site it is necessary to enable JavaScript.
EMIN.COM.LA
0

ຂ່າວ EMIN

Coating Adhesion Test Methods for Reliable Inspection
18/09/y 10:10:46

A coating adhesion tester is an essential instrument for evaluating the quality of paints, varnishes, and protective coating systems. The coating must bond sufficiently well to the substrate or underlying coating layer to minimize peeling during use. Depending on the substrate material, coating system structure, test conditions, and evaluation objectives, operators can select from several adhesion test methods, including knife, tape, pull-off, and scratch tests.

Ultrasonic Coating Thickness Measurement on Wood
18/09/y 10:06:58

A practical overview of ultrasonic coating thickness measurement for wood and wood products, including operating principles, measurement considerations, and process-control benefits.

Screen Printing Thickness Measurement Guide
18/09/y 10:05:45

The PosiTector 6000 FS1 is a non-destructive coating thickness gauge that enables the monitoring of mesh, emulsion, stencil, and dried ink thicknesses in the screen printing process.

5 Signs of a Weak Signal on a Spectrum Analyzer
17/09/y 09:02:30

When testing a radio system, a low-level signal on a Spectrum Analyzer does not necessarily mean that the transmitter is weak. The power level measured at the analyzer input depends on many factors along the entire signal path, including cables, connectors, filters, splitters, amplifiers, antennas, and the transmission environment.

Why Does a Soldering Iron Heat Up Quickly but Still Solder Slowly ?
16/09/y 11:04:47

Before contacting the material, a handheld soldering iron mainly heats the soldering tip. Once soldering begins, heat is continuously transferred from the tip to the material. If the heat supply is not sufficient to compensate for heat loss, the temperature at the contact area drops and the processing time increases

Decoding the Challenges of Semiconductor Chip Testing
15/09/y 13:57:41

In the semiconductor testing and measurement sector—where every nanosecond and microvolt can determine the success or failure of a chip design—choosing the right test equipment has never been simply a matter of comparing specifications on paper.

The desoldering tool determines the heat recovery rate, not the suction power
14/09/y 16:20:13

Many people choose a desoldering tool by comparing the wattage rating on the casing, assuming that higher power equates to stronger, cleaner suction. This is a common misconception; power output relates solely to the heating element and is entirely independent of suction force, which is determined by the vacuum pump

ຕິດຕາມຂ່າວສານ ແລະ ຂໍ້ສະເໜີ

ຮັບສ່ວນຫຼຸດພິເສດຕາມປະລິມານ, ອັບເດດລາຄາຂາຍສົ່ງ ແລະ ການແຈ້ງເຕືອນສິນຄ້າໃໝ່ສົ່ງກົງເຖິງອິນບັອກຂອງທ່ານ.

ໂດຍການສະໝັກສະມາຊິກ, ທ່ານຍອມຮັບ ເງື່ອນໄຂການໃຫ້ບໍລິການ ແລະ ນະໂຍບາຍຄວາມເປັນສ່ວນຕົວ ຂອງພວກເຮົາ.

ການຊ່ວຍເຫຼືໍາດ່ວນ

ເຂົ້າເຖິງຜູ້ຊ່ຽວຊານທີ່ໄດ້ຮັບການຢັ້ງຢືນຂອງພວກເຮົາໂດຍກົງ