20/05/y 17:31:43
Sự khác biệt giữa buồng thử nhiệt độ dạng đứng và loại để bàn không chỉ nằm ở kích thước thiết bị. Quan trọng hơn, mỗi cấu trúc buồng lại tạo ra một kiểu tác động nhiệt hoàn toàn khác lên mẫu thử.
ຂ່າວ EMIN
Sự khác biệt giữa buồng thử nhiệt độ dạng đứng và loại để bàn không chỉ nằm ở kích thước thiết bị. Quan trọng hơn, mỗi cấu trúc buồng lại tạo ra một kiểu tác động nhiệt hoàn toàn khác lên mẫu thử.
In the era of Smart Manufacturing and Digital Factories, managing and tracing product origins through barcodes (Barcode/Data Matrix) has become a rigorous standard.
When looking at the specifications of an electronic depth gauge, most people immediately notice the smallest division, the measuring range, or the water resistance. However, on the side of many models, there is an additional small port marked SPC
When looking to buy a depth gauge, many people immediately look at the resolution because smaller numbers often give the impression of being more high-end. A display with 0.001 mm accuracy is quite appealing, especially with newer electronic models.
If you've observed electronics labs in recent years, you'll notice that the way they choose pulse generators has changed considerably. Previously, most attention was focused on specifications. The higher the MHz, the more waveforms, or the larger the display, the more likely the generator was to be preferred because it gave the impression of being durable and not becoming obsolete in the long run
A pulse generator might look very powerful in a catalog, but when you actually test it in a real circuit, quite a few annoying issues start to emerge. Some models produce a beautiful sine wave but have slight ripple at the edges of the pulse; some require many steps to change the waveform; and some models develop a loss of smoothness in the rotary knob or noticeably slow menu response after only a few months of use
Sometimes, a pulse signal may appear perfectly normal at first glance, but when viewed on an oscilloscope, it reveals slight vibrations, uneven amplitude, or timing deviations in cycles. The first reaction is usually to check the pulse generator, connections, or output load. However, many errors originate from the power supply section, especially the switching power supply
In many drive systems, people often only pay attention to whether the machine is still running, whether there are any unusually loud noises, or whether the motor temperature has risen excessively. But there is a rather subtle parameter that directly affects the durability of the entire drive system: RPM, or the actual rotational speed of the deviceIn many drive systems, people often only pay attention to whether the machine is still running, whether there are any unusually loud noises, or whether the motor temperature has risen excessively. But there is a rather subtle parameter that directly affects the durability of the entire drive system: RPM, or the actual rotational speed of the device
In many mechanical workshops or QC departments, there's an interesting detail: the more surface measurement work is involved, the more granite surface plates are preferred over steel or aluminum. At first glance, this seems counterintuitive, as metal always feels much harder, stronger, and more "industrial" than stone
Increasing electricity costs month after month, even though the compressed air system is functioning normally, is a common situation faced by many factories. The compressor hasn't reported any errors, and the pressure is sufficient, so everything seems fine at first glance. Only during a thorough inspection do numerous leaks, long-standing and largely unnoticed, are discovered
ຮັບສ່ວນຫຼຸດພິເສດຕາມປະລິມານ, ອັບເດດລາຄາຂາຍສົ່ງ ແລະ ການແຈ້ງເຕືອນສິນຄ້າໃໝ່ສົ່ງກົງເຖິງອິນບັອກຂອງທ່ານ.
ໂດຍການສະໝັກສະມາຊິກ, ທ່ານຍອມຮັບ ເງື່ອນໄຂການໃຫ້ບໍລິການ ແລະ ນະໂຍບາຍຄວາມເປັນສ່ວນຕົວ ຂອງພວກເຮົາ.